What Size Do Dowels Come In?

Dowels are great to reinforce wooden joints or to support shelving units. They are small rods that can be bought either in standard sizes or as large rods and cut down to the required size.

Dowel Sizes

The dimension most commonly referred to when measuring dowels is diameter or width. This is because you need to be able to match your drill bit with the width of the dowels you are using.

Getting The Right Size

Plastic dowels can even be cut to size with a sharp cake knife. The length of the dowel you cut will depend on the DIY task you’ve taken on. For example, if you’re repairing a screw hole, you’ll be cutting a dowel peg that’s roughly the same size as the screw that fits it, whereas making an axle for a toy car will require a dowel that’s as wide as the car you’re making. It’s relatively easy to adjust the length of a dowel because you can just cut them, even if they’re made of metal or plastic. Reducing the width is much more difficult to do accurately.

Availability

Dowels come in a large variety of widths which may be measured in metric (millimetres) or imperial (inches) units. Dowel pegs sizes are usually listed in millimetres, but dowel rods may be listed either in millimetres or inches. Dowel rods usually come in widths between 3.175mm (1/8″) and 50.8mm (2″), but they can be as wide as 304.8mm (12″). They are usually between 304.8mm (12″) and 2.4m (9431/64) long.

Standards

Pre-cut dowels are usually either 6mm (¼”) wide and 30mm (13/16″) long, or 8mm (5/16″) or 10mm (3/8″) wide and 40mm (19/16″) long. When buying specific equipment for dowelling, such as drill bits, drill stops and centre points, these sizes are considered standard.

Source: https://www.wonkeedonkeetools.co.uk/dowels/what-sizes-do-dowels-come-in

Drawer Boxes

If you’re looking for the best quality cabinet drawer boxes at the best prices there isn’t a better source than Drawer Connection.  We give you your choice of wood and only source the highest quality raw materials.  All of our fabrication is high precision and made to last.  Whether you’re choosing a solid wood with a dovetail joint or a melamine with a dowel joint, every single drawer box is built to last!

The Best Wood Choice For Drawer Bottoms

Hardwood plywood is generally considered by experts to be the best wood for drawer bottoms – but it is important to understand the characteristics of plywood, so you know what to look for. Read on to learn more.

Marine plywood, despite its name, is not waterproof and as it is not treated with any chemicals, it not resistant to rot. Nonetheless, it remains good quality made with waterproof glue. better grades of the material are often strong, lightweight and virtually defect free. This makes it ideal for drawer bottoms and also has applications for boat parts and boats.

Other Strong Woods

Woods that have a natural resistance to decaying sich as redwood, cedar, cypress and shorea have a natural resistance to decay but the price and quality of these materils can vary although they are in essence a naturally strong form of wood. Conversely, marine plywood is not pressure-treated and if it is exposed to moisture, it will require a finish that is water resistant.

What Makes Plywood Strong?

Wood veneer is made of sheets or layers known as piles. They arrange the sheets in layers that are perpendicular and this gives the plywood strngth (Golf woods were made from laminated maple for decades and were very strong and durable.) Every piece of plywood has an odd number of layers and the process of cross-lamination arranges the piles in a manner so they are perpendicular to each other. The plywood is then fully bonded with pressure and heat.

Waterproof Glue

If plywood is exposed to moisture, the glue will not fail (one reason it was popular for golf woods) and the wood layers will not delaminate. Not only it is important in drawer boxes but also has marine applications in boats and so on.

Good Plywood

Plywood is usually graded (A,B,C,D) with A being the best – but they are not thought of as being of as high a quality as marine and other forms of hardwood plywood. True hardwood plywood is made with thin layers of one hundred percent hardwood that is normally stronger and harder and has a finer grain the hardwood. Plywood that is sold as being “void-free” lacks voids in the layers of wood. Many thin layers are bettter than fewer thicker layers because the thinner layers relate in a stronger, denser panel of wood.

Drawer Boxes

If you’re looking for the best quality cabinet drawer boxes at the best prices there isn’t a better source than Drawer Connection.  We give you your choice of wood and only source the highest quality raw materials.  All of our fabrication is high precision and made to last.  Whether you’re choosing a solid wood with a dovetail joint or a melamine with a dowel joint, every single drawer box is built to last!

Advantages Of Pinewood

Pine has many advantages as a material for all kinds of furniture and cabinetry. Read on to learn more.

Pricing

Often cheaper than oak, because of the fact pine is fast growing and need less care so they can come to market more quickly and this makes the price lower making it attractive to many people.

Coloring

Its natural light coloring means it looks great inthe home. It is versatile and goes with various wall colors, patterns and other decorations.

Options

Pine can be easily colored or stained and fives you a wide variety of finishing options. Or you can keep it natural with a clearcoat.

Stiffness

As a pretty stiff wood, pine is very strong and durable.

Light Weight

Pine has the advantage of being sturdy and lighter in weight than oak. Its lightweight makes it ideal when you want to move furniture around. It is also very resistant to shock.

Distinctive Looks

With its very distinctive look with dark knots, it is very well worth considering among wood choices.

Drawer Boxes

If you’re looking for the best quality cabinet drawer boxes at the best prices there isn’t a better source than Drawer Connection.  We give you your choice of wood and only source the highest quality raw materials.  All of our fabrication is high precision and made to last.  Whether you’re choosing a solid wood with a dovetail joint or a melamine with a dowel joint, every single drawer box is built to last!

How to Install Bottom-Mount Drawer Slides

Installing Bottom-Mount Drawer Slides

If you are updating your bathroom or retrofitting new cabinetry, deciding on the right drawer slide can be daunting. With so many options to out there; mount, extension type, slide length, limits on weight, and finishes, how do you know which one to choose for your project? In this post we will discuss one of the most popular, bottom mount.

Tools You Will Need:

  • Safety Glasses
  • Saw
  • Screwdriver or Drill
  • Tape Measure
  • Pencil
  • Chisel
  • Hammer
  • Nails
  • Level
  • Combination Square

*Warning*

When using with power tools, always wear safety glasses to help protect your eyes from debris.

Why Choose A Bottom Mount Drawer Slide?

Using this mounting method allows you to have your drawers almost the full width of the drawer opening—minus 1⁄8 inch on each side, giving you more storage space than with other types of slides.

Using one slide (around $8 to $20 per pair) in the middle of the drawer keeps hardware costs down.

When you use one slide for each drawer, it reduces the weight-carrying volume to less than half that of a similar drawer that has two slides. (Single bottom-mount slides typically rate for 25-pound volume.) For the mounting screws to take hold, you will need to make your drawer bottoms 1⁄2 inch thick, or possibly add a space if you are using thinner bottoms. A lot of bottom-mount slides are 3⁄8 inch thick but leave 5⁄16 of an inch underneath your drawer bottom for mounting. The additional 1⁄16 inch provides clearance between the sides of the drawer and the face frame after being mounted.

Attach To The Drawer First

  1. For drawers that are inset, align the slide adjacent with the front of the drawer and positioned across its width. If your drawers will have a front overlay, notch the drawer box, so the slide sits adjacent with the drawer boxes front face.

Cut a notch for the slide at a minimum of 1/8 inch wider on each side, to the drawer bottoms depth. Then using a chisel, take out the waste.

  1. Center the slide and fasten it with screws at the back and the front.

With one screw retaining the front of the slide, using a measuring tape, measure from the drawer side to be sure that the slide is parallel and centered.

Add The Cabinet Mount

  1. Install the slide to the front of the face frame, attaching it with one screw. For drawers that are inset, first, attach a mounting block 3⁄4 inch thick inside the face frame in which you can screw the slide.

Be sure to mount the slide 1/32 inch back from the front of the face frame. You may need to angle the screw a little bit to keep clear of the above frame.

    1. Attach the slide to the back of the cabinet using a mounting bracket, make sure it’s square to the face frame. If your cabinets have a dust frame, you can mount the slide to it rather than the back.
    2. To aid in supporting the drawer, add self-adhesive or nail-in glide pads to the face frame where the drawer-side bottom edges are allowed to pass.

Glide Pads

Glide pads not only stop the drawer from rocking on an individual slide, but they also make drawer operation smoother.

Nationwide Drawer Slide Supplier

If you have broken drawer slides, or are maybe starting a new cabinetry project, or are just remodeling your kitchen or office, Drawer Connection has the widest selection of drawer slides in Phoenix. We have soft close, push to open, self-close, and many more quality options that keep your drawers opening and closing smoothly. Visit our site to get started or call us today at 877-917-4887.

Wood Joint Pros & Cons

Wood Joinery Pros & Cons

Are you searching for the Pros & Cons Of Wood Joinery? If so, this article should help!  There are many different wood joinery methods to choose from.  Depending on the project one may work better than another.  Learn all about the various woodworking joint types in this post!

What is Wood Joinery?

Replacement Drawer Box Page Divder

Wood joinery is marrying 2 pieces of wood into a single joint, it is an ancient craft which is used for making furniture, flooring, framing, and cabinetry. How easy the production of wood joints is depends on what is being constructed. Each project will also be different on its strengths and its purpose.

Pros & Cons Of Wood Joinery

Replacement Drawer Box Page Divder

There are different joints used for different projects, for not all wood joints are made the same. You will find that there are some advantages and also disadvantages in the different methods of wood joining, as well as for each of the species of wood that are joined.

Butt Joint Pros & Cons 

Replacement Drawer Box Page DivderButt Joint Pros & Cons

When joining wood joints together, you will find that the easiest to join will be the butt joint. The joint butt is merely gluing one piece of wood to another piece. An end grain of wood is joined to a long grain of wood by the weakest sections using plates, pins, and/or dowels to reinforce the connection so that it is going to stand up to a certain amount of pressure. A butt joint can be broken apart with your hands if it is not stabilized.

Dovetail Joint Pros & Cons 

Replacement Drawer Box Page DivderDovetail-Joint-Pros-Cons

The most common place you are going to see a dovetail joint is on the front of drawers, as they are used to connect them together. Pins extend from one of the boards and is connected to tails that are cut on the end of the adjoining board. The dovetail joint will be extremely strong and is resistant to pulling apart. This is because after it has been glued there are pins and tails that are trapezoidal-shaped that take on a permanent hold. There will be no need for nails. This type of joint may be too hard for a beginner, as it needs precision cutting.

Dowel Joint Pros & Cons 

Replacement Drawer Box Page Divder

Dowel joints help to remove the need for screws, staples and nails. This helps to remove the potential injuries that often happen while working with hardware, but it can also help to give the project a more finished look as there is nothing to disrupt the grain pattern.

Dowel Joint Pros

Replacement Drawer Box Page Divder

  • Dowling is a quick process.
  • It helps to ensure a neat finish.
  • There is no need for screws, nails or other equipment.
  • Dowel joints are the strongest type of joints when it comes to woodworking, especially when using multiple rows of dowels.
  • Dowels help to create strong joints that are easy to make at home.

Dowel Joint Cons

Replacement Drawer Box Page Divder

  • Misalignment Of Joints
  • Dowel Shearing
  • Weaker Joint
  • No Face To Face Grain Contact

Read more from our other post about the advantages and disadvantages of Dowel Joints.

Mortise And Tenon Joint Advantages 

Replacement Drawer Box Page Divder

Mortise & Tenon is used generally when corner joints need to have sturdy frames for making things such as doors, tables, windows, and beds. A rectangular slot is referred to as a Mortise cut, and it is cut into the (exact) center of the end piece of wood so that it will except the protuberance fitting (the Tenon), thus, making a clean, strong joint. After it has been glued and well fitted, the wood joints will not move, and will be very hard to get apart. To be sure that the mortise is perfectly one-third as thick as the wood, it has to have precise measurements, this is to avoid any splitting of the mortise, and Tenon breakage.

Finger Joint Pros & Cons

Replacement Drawer Box Page Divder

Finger Joint Pros

  • Makes a straighter joint
  • Less wood gets wasted during manufacturing
  • Cost Effective
  • Durable for a vertical load
  • Adhesives can be applied to create a stronger joint than mortise and tenon

Finger Joint Cons

  • Can come out crooked
  • Harder to achieve a smooth wall

Bridle Joint Pros & Cons

Replacement Drawer Box Page Divder

Bridle joints are similar to mortise and tenon but the tenon and other member are cut to slot into each other.  These are popular joints for frames and to join rails, legs, and stiles.

Bridle Joint Pros

  • Simpler alternative to the mortise and tenon joint
  • Can shape joint assembly and not sacrifice strength
  • Great for constructing narrow frames
  • One of the simplest joints to cut
  • Doesn’t require a mortising machine

Bridle Joint Cons

  • Can see end grain which makes it less attractive

Rebate Joint Pros & Cons 

Replacement Drawer Box Page Divder

A rebate joint has commonalities to the butt joint in woodworking.  The biggest difference between the two is a groove that is cut out of one of the ends that increases holding strength.  It is used most commonly when a simple joint is wanted but when strength is required.  It is used commonly in cabinet  making and other carpentry projects.  In some cases dowels, screws, or nails can be added to increase the strength for load bearing joints.    The surfaces of a rebate joint are typically big enough that timber blocks shouldn’t be necessary.

Tongue & Groove Joint Pros & Cons 

Replacement Drawer Box Page Divder

You are going to need a tongue and grove joint when joining a wood edge to another wood edge, like if you were making a tabletop, laminating a floor, or connecting hardwood or paneling. The entire length of one piece has to be slotted or grooved so that it accepts the tongue cut that runs down the edge of the adjoining piece. The boards will be drawn together (without any lateral pressure), and they remain this way. Depending on what the product is, glue may not be necessary to use. It is easier to measure the Tongue and grove joints, and also easy to produce if you use a router having a depth setting capability.

High Quality Joint Drawer Boxes

Replacement Drawer Box Page Divder

If you’re in the market for drawer boxes DC Drawers proudly crafts the best cabinet drawer boxes using the dowel joint or durable dovetail joint.  When you place your order with DC Drawers you’re getting the best quality, fastest turnaround, and best prices anywhere.  Shop dovetail drawer boxes or dowel drawer boxes.

Thank you for reading “Wood Joint Pros & Cons“! Stay tuned for more from the expert drawer box manufacturers at DCDrawers.com

What’s The Best Wood For Cabinetry?

The best wood for cabinetry is widely considered either red oak, poplar, maple, mahogany, or plywood.  Which solid wood type is best for a specific project depends on budget, if the cabinetry will be painted, and personal preference.

Everyone wants to know that the home improvements they’re making are durable and add real value to the property.  So what is the best wood for your cabinets, drawer boxes, and cabinet doors?  

    1. Best Wood For Cabinetry
      1. Cherry, Maple, Ash, Hickory & Oak
      2. Birch, Beech, White Oak, & Red Oak
      3. Walnut & Mahogany
      4. Spruce, Pine, & Fir Softwoods
      5. Plywood
    2. Best Wood For Painted Cabinets
      1. Wood Grain Paint Challenges
    3. Best Wood For Painted Cupboards
    4. Order Cabinet Drawers

Read about each of the different types of wood in this article to judge for yourself which wood type you want for your cabinet doors, cabinet drawers, and home.

Best Wood For Cabinetry

Your bathroom and kitchen are focal points in your home.  That means that your cabinets need to be durable, functional, and attractive quality materials. Boxed or prefabricated cabinets are built using low grade, thin materials that are overlaid with a wood veneer. Cabinets are built using hardwood solids and plywood, and both materials will matter when you are picking what is best.

Cherry, Maple, Ash, Hickory and Oak

Cabinet doors and face frames are often made from solid hardwoods. Wood species such as hickory, maple or beech will resist scratching and denting at a higher degree when compared to other softer species like walnut, alder or mahogany, but they will also cost more.

Hickory and maple for example are two of the hardest wood species that are used for cabinets and are normally more expensive than softer woods like ash or oak. Although imported or exotic species no matter what the density is will normally cost more than domestic hardwoods.

Other exceptions do include domestic hardwoods that are trendy. Cherry for instance, because of the subtle, intricate grain pattern and warm rich color is considered a luxury wood. It will normally demand a higher price than other domestic woods.

Birch, Beech and White or Red Oak

One of the most commonly used hardwoods by cabinetmakers is medium priced red oak that has arched or complex flame grain patterns. White oak has straighter grains but it will cost more than red oak.

Other types of domestic species include beech woods that have straight graining and birch that has streak and bands of brown will be priced lower than beech because of the availability and the lost cost of birch plywood.

Walnut and Mahogany

Other types of commonly used hardwoods are the rich and dark brown walnuts and the straight grained red mahogany. Mahogany gives warmth while walnut, which is similar in cost and hardness to mahogany, happens to add elegance to cabinets.

Other wood species can be stained to match existing colors that are in the home, although some will react to staining better than other wood. Ash, pine, and oak absorb stains evenly. While Birch and maple can blotch if not prepared for stain. Walnut and cherry which are known for their colors, are better left as is.

Spruce, Pine and Fir Softwoods

Cone bearing evergreen trees provide softwoods, which are normally used for structural purposes. Whenever it is used for cabinets, softwood like pine will give a certain look to cabins, cottages, lodges and country settings with the knotty character and soft tones of amber.

Other softwoods like spruce and fir will be straight grained but they are tougher and harder than pine. These are normally used for utility or economy applications such as in shops or garages.

Cabinet Grade Plywood

Plywood is a glued and laminated wood that is engineered and overlaid with hardwood veneer and is normally less than 1/16 inch. The appearance of this is the only difference when it comes to comparing grades which is important for determining cost and quality. Plywood that is designated AA or premium will be the most expensive. It is often called one piece faced, the veneer is rotary cut in a single piece to keep it from splicing.

Grade A plywood is a bit cheaper than AA and the veneer is spliced side by side and color matched to give it consistency. Grades B, C, D, and E will be less expensive and will be lower grade in appearance with each lower level having inconsistent colors or additional streaks. Shop grade or economy plywood is the cheapest and it has allowed damage or defects. At least 85% of shop grade plywood is normally usable with a good cabinet maker that can work around the defects.

What is the best wood for painted cabinets?

Similarly, as any craftsman needs to choose what medium to utilize, woodworkers must choose what wood to work with. The appearance, shading, cost, planned utilize, workability, and maturing conduct are for the most part contemplations.

In any case, so is a wood’s paintability or capacity to take a stain. In the event that recoloring, you need to know how the wood grain will show and how the wood shading influences the shade of the stain. Here’s a snappy guide from the Pros who’ve addressed the inquiry, “What’s the best wood for painted cupboards?”

Wood Grain Paint Challenges

Paint-review wood has a tendency to be of the more tightly grained assortments, for example, hard maple, soft maple, pine, and poplar, among others. Open grain wood has a rougher look and likely needs filler to look great when painted. It’s best to work out of tight-grain woods to keep away from this.

Poplar and delicate maple are well known for most parts of a bureau—confront outlines, end edges, and entryway boards—for the most part because of cost and workability. In any case, a few craftsmen find that poplar marks effectively. It can likewise ingest the principal layer of paint rapidly.

A portion of the other tight-grain woods are somewhat less demanding to work with, yet their accessibility or cost isn’t viewed as a sufficient exchange off. Hard maple can be another great decision, despite the fact that it can move marginally more than different woods with changes in stickiness.

MDF can be utilized for face and end outlines. A few woodworkers utilize it for entryway boards, yet it can be dubious to wrap up. Along these lines, other wood assortments are regularly utilized for rails and stiles. MDF stays prominent as it is steady and hence useful for bigger pieces. Birch plywood or prefinished plywood is another possibility for these more drawn out segments.

So what’s the best wood for painted cupboards?

Similarly, as with most things, you won’t discover any deficiency of assessments, however there seems to be some expansive concession to when the best sorts of wood are for painted cupboards. Tight-grained woods that are workable and solid remain a prevalent decision. Whatever material you pick; the staggering understanding is to set up the wood’s surface first. Utilize filler if necessary, shellac on hitches so they don’t seep through, and be sure to sand over any sharp corner that may not hold the paint. Below is a fast breakdown of the forested areas commonly found in cupboards:

      • Hard Maple: light, dense. Grain: stainable, close grained, and fine textured
      • Hickory: durable, hard, and strong; white to reddish brown. Grain: coarse and straight
      • Cherry: Moderately heavy, strong, and hard; sands smooth. Grain: red and finishes beautifully
      • Soft Maple: strong, hard, and medium density; paint grade. Grain: fine textured, close grained
      • Mahogany: varies in color between medium red to reddish brown. Grain: medium coarse texture, straight to interlocked grain
      • Beech: heavy, medium to hard, pale colored; stains and polishes well. Grain: tight and fine. Similar to birch and maple
      • Alder: Reddish brown color, easily dented. Grain: straight grain, even texture
      • Red Oak: heavy, very hard, and strong. Grain: coarse texture with easy sanding and finishing
      • Red Birch: red in color softer than red oak. Grain: tight grain, easy to finish
      • Douglas Fir: light rosy color that will redden. Grain: tight knotted and close grained
      • White Oak: light to dark brown in color, heavy and hard. Grain: straight grained with medium to coarse texture
      • Knotty Pine: lightweight with tight and small knots. Grain: straight with an even, fine texture

High Quality Cabinet Drawer Boxes

If you’re looking for the best quality cabinet drawer boxes at the best prices there isn’t a better source than Drawer Connection.  We give you your choice of wood and only source the highest quality raw materials.  All of our fabrication is high precision and made to last.  Whether you’re choosing a solid wood with a dovetail joint or a melamine with a dowel joint, every single drawer box is built to last!

In Drawer Charging Stations For Kitchens & Bathrooms

in-drawer-charging-stations-for-kitchens-bathrooms

When you’re searching for a in drawer charging station or in drawer power outlet we have the outlet and charging solutions you’re looking for.  From USB charging stations to 120 volt power outlets for hair dryers or appliances we have a full range of in drawer power solutions.

In Drawer USB Charging & Power Outlets

These combination outlets offer USB charging ports along with standard power outlets for electronics.  They are great for smart watches, laptops, mobile phones, tablets, and electronics that draw 3 amps or less.   They are not made for high power items such as hair curlers or hair dryers.

Simply plug in your USB cord or plug into one of the outlets to put away your devices and allow them to charge.  This cleans off your countertops in your kitchen and bathroom.

In Drawer Power Outlets For Appliances

Whether it’s the kitchen or the bathroom having power outlets in your drawers makes it a snap to use your daily electronics and appliances.  Whether it be your hair dryer, curling iron, blender, mixer, or personal electronics such as a tablet or smartphone everything will be ready to use when you need it.

You won’t be searching for an outlet to plug your mixer or blender in.  Simply lift the mixer out and turn it on.  No need to unplug your toaster next time you’re ready to make a smoothie.  Just use, clean, and simplify your life.

Kitchen Drawer Charging Stations

The kitchen is fast becoming a family meeting and favorite social area. With quieter dish washers and finer cabinetry, countertops, and dining tables it is a great place to enjoy each other’s company. Keeping our tablets, smartphones, laptops, and other electronics charged and ready for action is a must in today’s ever increasingly digital world. Being able to also have a spot to charge your USB devices without wall adapters makes life simpler. This means more than just your smartphone or tablet, but also USB speakers, or USB flashlights.

Bathroom Drawer Charging Stations

For bathrooms the use of hair dryers, curling irons, flat irons, and other hair care electronics is very common. Having all of the hair care tools laying out on the counter adds to clutter and cuts down on the counter space to have all of the other hygiene and beauty items we all use.

Being able to simply open a drawer, grab the plow dryer, and switch it on without having to find the end of the cord and find an available outlet makes mornings easier. It also makes it easier to keep our houses organized and free from clutter. Not all drawer charging or power stations are made to handle the amps that these items require. This means that heavier duty in-drawer power outlets are necessary.

Plug In Drawer Charging Systems

These drawer power systems are simple to install and to hook up to your house’s power. They simply plug into a regular power outlet. There are options for charging systems that you use with your wall charging power converter, and those that are ready to just simply plug in 4 of your higher power personal devices without the use of the AC adapters.

Hard Wire Drawer Charging Systems

These are the best option when you need to plug in your high power or high amperage electronic devices. These are necessary for the bathroom applications as hair dryers, hot irons and the like draw a good amount of power and need to be plugged into a regular outlet with a GFCI. GFCI stands for Ground Fault Circuit Interrupter, and it is an important safety feature. It cuts the power to an outlet when it senses that the power is taking an unintended path, such as through a person or water. That means it keeps you safe if your hands are wet or the hair dryer falls in a sink full of water.

Choosing The Right Drawer Charging System

Depending on your needs you can choose from charging systems that only have low draw outlets or USB ports, or you can use the more robust GFCI hardwired outlets for your higher power devices and appliances. If you want the simplicity of being and to just have a USB wire plugged into a USB port in your drawer a slim USB charging system will work for you.

If you want the flexibility of plugging any low power personal electronic device choosing a unit that has regular 2 prong outlets is a great choice. For 3 prong electronic devices like hair dryers you will need to invest in drawer outlet systems that are rated to deliver that much power, and have a licensed electrician install the drawer. This keeps you safe and ensures that it has been done correctly to keep you safe.

Shop Drawers With Power Outlets at DCDrawers.com.

Premade Drawer Boxes

Premade Drawer Boxes

When you search for premade drawers, custom drawers, or premade drawer boxes our high quality precision made options fit any build.  They can be ordered as dowel joint or dovetail joint drawers and are perfect for any kitchen or bathroom project.  It’s easy, affordable, and simple to order your drawer boxes from Drawer Connection Inc.

Contact Us or Call 877-917-4887 

Shop Premade Drawers

pull-out-drawer-kits

At DC Drawers, we pride ourselves on delivering high quality premade drawer boxes at an affordable price! That’s why we only manufacture the best quality dowel & dovetail drawers for multiple applications and industries including skilled cabinet making and remodeling.  We sell drawer boxes individually and supply cabinetry companies and general contractors.

Whether you choose premade Maple, Plywood, Birchwood, PBC, MDF, or Melamine drawer boxes, you can feel comfortable knowing that the same quality woodworking and workmanship will go into every drawer we build. Ask about our FSC® certified products.

Why Outsource Premade Drawer Boxes?

pull-out-drawer-kits

Custom bathroom and kitchen cabinetry shops have the ability to outsource just about every component that goes into making their goods. From body components to dovetail drawer boxes virtually everything can be found premade and can be simply ordered and delivered.

Each cabinetry company needs to decide if outsourcing premade drawer boxes and other components is a good idea. Some premade component companies have little to no ability to customize to fit the needs of the cabinet maker, or the homeowner’s preferences.

Focuses Your Skilled Labor

pull-out-drawer-kits

Focuses-Your-Skilled-Labor

Being able to deliver your custom bathroom and kitchen cabinetry on time, especially if you have a lot of jobs going, depends on quick production and turn around. Custom making ever single piece of cabinets takes the time of skilled craftsmen that could spend more time installing, and less time fabricating if some of the components were outsourced.

While some companies choose to outsource nearly all of their components such as the cabinet doors, frame, drawer fronts, and roll out trays, many cabinet makers choose to get the drawer boxes premade and simply delivered. This saves a ton of time in fabricating one of the internal components of the cabinets.

When you have lead men building your drawers, You run the risk of:

  • Slower Lead Times
  • Lost Revenue
  • Production Mistakes

Long Term Durability

pull-out-drawer-kits

long-term-durability-drawer-boxes

Quality is still key in every part of the build and care must be taken to choose professionally made, reliable, premade drawer boxes. The quality of the joints, whether they be dovetail or dowel joints, will decide how long the drawers last.

Word of mouth reputation is one of the strongest forms of advertising, and people cannot seem to help but show off their beautifully remodeled kitchens. Over the years if things were cheaply made, or not chosen well by the cabinet makers customers will become dissatisfied and their friends, family, and facebook will know about it.

Benefits Of Premade Drawers: 

pull-out-drawer-kits

  • High quality drawer construction
  • Affordably priced premade drawer boxes
  • Increase Production
  • Decrease Mistakes
  • Generate Revenues
  • We design to your custom specs and 7-Day Turnaround Melamines and Plywoods.
  • Emergency Services @ No additional Charge
  • 10-12 Day Turnaround on Solid Materials
  • 24 Hour Online Ordering

More Advantages Of Outsourcing

pull-out-drawer-kits

Outsourcing-Drawer-Boxes-Saves-TimeTime – You have a lot of jobs going and having your skilled labor putting together drawer boxes is a waste of their skills. They could be installing, or fabricating the critical or signature components of your particular designs.

Outsourcing-Drawer-Boxes-Opens-Up-SpaceSpace – Each type of custom made part you use in your cabinetry requires space for raw materials, a place to assemble, and a place to store the completed drawer boxes. Outsourcing their construction opens up space in your shop for more custom cabinet components.

Outsourcing-Drawer-Boxes-Saves-MoneyMoney – The cost of paying your skilled labor and cabinetry experts to make drawer boxes costs more than simply ordering them from premade drawer box companies.  Premade fabricators do one thing, and do it all day every day. This helps cut down on the time it takes to make the boxes, and what it costs to produce them.

Consistent-Quality-Drawer-BoxesConsistent Quality – Because it is simply the only thing that is built at these factories the machines are dialed in and the builders are completely focused on quality of drawer boxes. They are no rushing to get to the next jobsite or back to another project. They are simply focused on making the best drawer boxes on the market.


Premade Drawer Boxes by Drawer Connection

Drawer Connection has the ability to help you meet the needs of your clients. We build the drawer boxes so your skilled labor can focus on the intricate details of the cabinet doors, drawer fronts, and all the other signature components of your cabinetry company.

Outsourcing the fabrication of the drawer boxes helps you get the job done faster, and handle more jobs at one time. Create an account online to start shopping for quality premade drawers today!

Give us a call at 877-917-4887 to get your order started today! Shop Cheap Drawer Boxes at DCDrawers.com

Related Content You Might Like:

Best Wood For Drawers

 If you’re searching for the best wood for drawers you might be a homeowner, new cabinet installer, or a general contractor trying to make decisions about what drawer boxes to order. Whether it is a new build or you are remodeling a kitchen choosing quality parts such as drawer boxes is important.  The wood you choose to install will speak to the durability and quality your company installs, or you chose to install in your own home.

Choosing The Right Wood

The wood workers that make cabinetry using hardwood that is more expensive and attractive have their uncertainties when it comes to what they should use for the construction of the cabinetry drawers. They will be overwhelmed with thoughts such as, “should the back, bottom, and the interior sides, of the drawers be made from the same material as the cabinet and drawers? The drawer sides would match with the front of the drawer, as well as the rest of the cabinet, it would certainly be a uniformed look, but would it be too much and over stated?

Cherry Wood Is Expensive

However, when building drawers in this matter it may be an advantage to use different types of wood. The first reason is that hardwood like cherry and fine maple will be very expensive. If it was going to be for a rather large project, such as a wall entertainment center, the cost will quickly add up. The second reason is that it is usually difficult to fine cherry and some of the other hardwoods in veneer plywood. Which also means that the bottom pieces of the drawers would have to be glued together from a stock pile, and would consist of a lot of time.

Lastly, it could end up being a stylistic advantage to use wood for a contrast on the sides of the drawers. For the drawer box, a light colored wood such as poplar, made into half-tailed dovetails for instance, would show the workmanship off.

Best Wood For Drawer Boxes

An excellent choice for the construction of drawers is maple. Maple drawer boxes are an excellent option for a number of reasons. This is because it is stable, less expensive than most other hardwoods, and its durable. It also blends very well with a birch plywood, which would be used for drawer bottoms.

Ultimately it is up to each contractor, cabinet installer, and homeowner to decide which material fits the project better for quality, durability, and budget.  Use this information as a guide to understanding your options and choose wisely.

Here are two reasons that plywood is used and not solid wood:

  • The use of plywood only consists of cutting for the final dimensions, jointing together, and finalizing it down to size.
  • No longer than what they will be looked at when opened it is not necessary to worry about whether or not they are made of solid wood.

Order The Best Wood Drawer Boxes

If you are building or remodeling cabinetry in a bathroom or a kitchen and need new drawer boxes, we are your source for the highest quality at the best prices.  We ship the best wood drawers nationwide in the United States and are proud to fabricate your drawer boxes right here in America.

Shop: Dovetail Drawer Boxes – Shop: Dowel Drawer Boxes

How To Replace Kitchen Drawers

If you are searching for “How To Replace Kitchen Drawers“, “Replace Kitchen Drawers“, or “Replace Kitchen Cabinet Drawers“; Drawer Connection can help!  We will also show you how to order a replacement drawer, or build the drawer yourself!

How To Replace Kitchen Drawers

Accidents happen and if you’ve got a broken drawer in your kitchen you’ll want to fix it so you don’t have items falling out of your drawers.  Parts of homes wear out and the drawers in our kitchens are no different. When they break it can be frustrating to lose the storage space and an eyesore having an open gap.

Some “quick-and-dirty” handymen will do things like nail or glue the drawer front back in place and just forget there ever was a drawer, perhaps to make a tee time or get back to watching TV. Learning how to replace kitchen drawers need not be a painful project, let us show you how here.

Kitchen Drawer Replacement Steps

Use this step by step guide to learn how to replace kitchen drawers and where to buy replacement drawer boxes:

1. Measure The Replacement

To get started you will need to know the size of the replacement you need. Get the height, width, and depth of the opening for the replacement drawer.  Take off an inch for your height and width measurements and at minimum of a half inch from the depth which will allow for easy fitting and drawer slides.

2. Build or Buy a Replacement Drawer Box

Drawer boxes are typically custom built for each kitchen so heading down to the local Walmart to pick up a replacement isn’t an option. To get a replacement that will work you will either need to build a replacement, have a friend do it, or order a drawer box from a professional.

Custom made cheap replacement cabinet drawers can be made in your choice of material, using either dovetail joints or dowel joints, in exactly the size you need.  A replacement drawer box measuring 18” wide by 20” deep by 4” high costs less than $30 dollars from Drawer Connection.

DIY Kitchen Drawer Replacement

Step 1. – Remove the broken drawer out of the cabinetry and put it on a table.  Take the drawer front off by removing the screws that hold it in place.

Step 2. – Flip the drawer over and remove the metal runners from the sides of the drawer.  If the bottom of the drawer falls out, just set it aside.

Step 3. – Tap on all the sides of the drawer to separate it into the 5 sections that make up a drawer, the 2 sides, front, back, and bottom.

Step 4. – Measure the sections of your drawer and use your table saw to rip new replacement sections.  You’ll need to match the lengths and widths of all the the sections.  The front, back, sides, and bottom need to be exact so the runners can be replaced and the drawer will fit correctly.

Step 5. – Using a 1/4 inch dado blade for your table saw prepare your table saw by setting the bland and fence to 1/4 inch.  Run the front, back, and sides through the saw to create a channel in each of the pieces.

Step 6. – Set all four of your sections together, as if they were already put together.  The side pieces should sit on the sides of the front and back sections.  The channel from step 5 should all sit at the bottom of the drawer at the same height.  Measure the inside of the width and length of the drawer and add 1/2 inch to each measurement.  Cut a section of 1/4 plywood to those measurements to be the bottom of your drawer.

Step 7. – Get some wood glue and run a bead where the drawer bottom will sit.  Set the bottom into the channel made for it ensuring there’s a nice coating of wood glue.  Use clamps to hold all of the sections together until the glue dries.  It’s a good idea to wipe off any excess glue at this stage.

Step 8. – Drill holes for the drawer front screws to go through that are 3/16ths thick.  Using screws that are 1 1/4″ attach the front back to the drawer box.  Reattach the metal runners on the drawer and screw them into lace using 3/4 screws.  Set your DIY drawer into place back in the cabinetry and you’re done.d

3. Buying Drawer Slides To Match

The next step is making sure you have drawer slides that match your drawer box depth. You can choose from inexpensive roller slides to ball bearing slides that have soft close and smooth opening features. Most homeowners prefer buying the bottom-mount style drawer slides as they have a piece which wraps around the lower edges of the drawer box and makes for easier installation. There are cases where old hardware from the slides is still intact and can be reused, but many homeowners prefer starting fresh when repairing their cabinet drawers.

4. Prepping The Work Area

Depending on why the drawer broke, and how quick and dirty the repairs where you might have very little work, or a lot of work to do here. If there is any broken wood or hardware it should be removed and replaced. This can mean any glue that was used as a band-aid to hold the drawer front on the face of the cabinets, or it can mean removing and replacing broken or splintered wood inside your cabinets to have a solid area to secure your new drawer.  For glues you can try heating the adhesive up with a blow dryer or you can simply use a scraper to work the glue off and then sand & repaint the area.

5. Installing The New Drawer Box

Once your drawer box arrives, you will want to wait to attach the drawer front until the drawer box is installed and sliding back and forth correctly.  It can be a bit tricky to align the drawer front right, using double-sided tape to tack the pieces together saves time and effort. When installing the drawer ensure that the gaps on the top, bottom, and sides are equal. Once you are sure the box is installed right you can use at least 2 screws to secure the drawer front to the drawer box, from the inside of the drawer.

Buy Replacement Kitchen Drawers @ Drawer Connection

Buy cheap replacement kitchen drawers at Drawer Connection.  You can also shop for replacement dovetail drawer boxes and dowel drawer boxes on Drawer Connection’s site.