Dowel Joint Advantages & Disadvantages

Are you searching the internet for “Dowel Joint Advantages and Disadvantages“? If so, this guide should help to understand joining wood with dowels. Here we list all of the advantages and disadvantages of dowel jointery.

Table Of Contents:

Use the links below to guide you to the section you are interested in.

 

Dowel Joint Advantages

Replacement Drawer Box Page Divder

  • Dowling is a quick process.
  • It helps to ensure a neat finish.
  • There is no need for screws, nails or other equipment.
  • Dowel joints are the strongest type of joints when it comes to woodworking, especially when using multiple rows of dowels.
  • Dowels help to create strong joints that are easy to make at home.

Dowel Joints happen to be a technique that is used in woodworking, where two wood pieces are attached by a dowel or wooden pin. In the wood pieces, a hole will be carved where the dowel goes. This is a way to attach wood pieces that you should think about the next time you are woodworking for the bottom reasons.

There’s No Need For Hardware

Replacement Drawer Box Page Divder

Dowel joints help to remove the need for screws, staples and nails. This helps to remove the potential injuries that often happen while working with hardware, but it can also help to give the project a more finished look as there is nothing to disrupt the grain pattern.

It Is Secure

Replacement Drawer Box Page Divder

The pin runs inside of the wood, so the joint is quite strong, and that is a lot stronger than using glue or nails to attach the wood.

Easy To Assemble

Replacement Drawer Box Page Divder

Once you have decided on how big the dowel needs to be, you have to hollow out the holes that the pin goes in. Just slide the pin in the piece of wood and then attach the other piece and that is it. It is that simple.

Versatility

Replacement Drawer Box Page Divder

The dowel joints are basically used in a right angle or flat angle joint because it can be made to work in more complex joints. The dowel joints can also be used in concrete construction and metal work.

Dowel Joint Disadvantages

Replacement Drawer Box Page Divder

  • Tenon and mortise joints are stronger, but it takes a lot longer to create
  • The alignment could be hard to get for beginners as it requires the use of a dowelling.

Disadvantages Posted by Customers

Replacement Drawer Box Page Divder

The main disadvantage is that they are weak. When it comes to tenon and mortise joints, the face grain cheeks of the tenon are completely in contact with the face grain side of the mortise. The glue also holds best in this situation. When it comes to dowel joints, there isn’t any face to face grain contact which causes the joint to be weaker.

Misalignment

Replacement Drawer Box Page Divder

When making a doweling joint, if the bit slips even just a little when starting the hole, or it isn’t lined up just right, you will have a lot of issues getting the joint aligned and/or getting the dowel in.

Besides the strength of the dowel joint, it is hard to get it aligned right, especially if there isn’t access to a drill press.

Dowel Shearing

Replacement Drawer Box Page Divder

Dowels will eventually shear. Then you have to drill it out and then insert a new dowel.  The higher quality dowels used the longer the drawers will last.

Shop Dowel Drawers with DCDrawers.com

Replacement Drawer Box Page Divder

Thank you for reading Advantages And Disadvantages Of Dowel Joints. Stay tuned for more from the expert drawer box manufacturers at DCDRAWERS.COM. Shop Dowel Drawers online.

Dovetail Drawer Construction Guide

Dovetail Drawer Construction Guide

Are you searching the internet for “Dovetail Drawer Construction“? If so, this guide should help.

Building a dovetail drawer happens to be one of the favorite things to do. I have always thought that were just for the best woodworkers, and it would be very hard and difficult to even master. While it does take some planning as well as careful setup, the average home woodworker should be able to achieve it.

First thing that should be mentioned is that the quality of the dovetail jig and your overall set up are very important for making a dovetail drawer. I love my dovetail jig that I got as a gift from Rockler. This jig is able to make various dovetail joints. For the drawers, I have used the half-blind dovetails.

Items Needed For Drawer Construction:

  • Dovetail jigs
  • Table saw
  • Router bushing and bit set
  • Surface planner
  • Plunge router
  • Miter saw
  • Sanders
  • Finishing supplies
  • Clamps

Step 1:

I normally make drawer boxes out of maple wood. These give the drawers a strong and resistant feel for everyday ear and tear. Although, because if the hardness, it isn’t as forgiving and for the first few practice runs this is a great choice. One important thing is that your materials need to be exactly sized and matched. I often will surface plane my materials to be between 5/8 inch and ½ inch and will use my joiner planner and table saw to make stock materials that are in exact inch multiples. The rockler dovetail jig will produce drawers that are even in height. Be sure that you are verifying the dovetail spacing on your jig before you start.

With the half-blind dovetails, the back and the front of the drawer will be cut to be the exact final width. For instance, I am using side mounted 100lbs ball bearing slides that need the drawer to be 1 inch narrower than the rough opening for a drawer. The sides are then cut to be ½ inch shorter than the wanted depth of the drawer. It is vital that you have selected the drawer slides before constructing your drawer to ensure that it will fit right.

Step 2:

The drawer back and front will then be loaded into the horizontal part of the jig and then clamped. The side will be positioned offset in the vertical part of the jig by integrated stop that will ensure a right ½ inch offset alignment. It is vital to know that you will be viewing the eventual inside of your box. Aligningthe teeth bar and back bar are going to be bested on the material thickness. Small amounts of change will result in larger changes in the final box, so ensure that you are making small adjustments. It is recommended that you test on scrap material before you move onto finished parts. Once done routing, each joint should be labeled as 1-4. The jig produces a matched set which will give you the best fit for joints that are cut in the same routing step.

Step 3:

Your router needs to be setup with the right dovetail bit and bushing. The bushing will ride along the jig teeth. The height of your bit will determine the tightness of the fit. I learned this myself after becoming frustrated with a fixed based router to use a plunge router with micro-height adjustable stop to dial in the joint. There is a differences that just 64th of an inch can change the joint from too loose to too tight. When you are using maple wood, you have to ensure that your joint isn’t too tight because it can cause the wood to crack with the final dovetail. Your joint should just need a gentle tap with a rubber mallet to get it together.

Step 4:

Once you have carefully set up the router, it will now be able to run around each of the jig teeth to provide a dovetail profile. You will begin to notice that the half-blind dovetailhas the tails and pockets on the inside of the drawer have become rounded. This is part of the joints that will become invisible once it has been put together. It is vital that you take your time to make sure that all of the materials have been removed properly. Once the jig has been dialed in, the drawers can be done quickly. It does take around the same amount of time for 10 drawers as just one drawer.

Step 5:

I prefer to use ½ inch plywood as the bottom of the drawer. ¼ inch material may be used for smaller drawers but it can cause it to sound quite hollow, or cause sagging in larger drawers. Because of this, I have begin to rabbit the edge off of the bottom to make the thickness 3/8 inch. This lets it fit in a dado to the drawer sides, which becomes invisible once it has been assembled. If a full ½ dado was used, it would show in the final dovetail joint. The dado for the bottom needs to be aligned with the center of the tail.

Step 6:

Your drawer should be dry fit with any type of fine adjustments that are made with sand paper or sharp chisel. The rabbited part of the drawer bottom needs to be towards the drawer bottom to make it invisible in the final product. Birch plywood may be used for the bottom because it looks like maple when it is finished. Although it is more expensive, maple plywood makes sure that the bottom and sides match when finished and it adds anextra nice touch.

Step 7:

Once a fit has been made, the drawer can then be glued and clamped. The whole surface of the dovetails will need to be coated in glue. Although, the bottom of the drawer shouldn’t be glued into the dado. The bottom needs to be sized to allow for contraction and expansion by being around 1/16 inch smaller than the maximum size that would fit into the dado slot. Dovetails will hold the drawer together without any clamping, but I do clamp mine to make sure that the drawers will be perfectly square while they are drying for a tight joint. For larger drawers, use multiple clamps.

Step 8:

Finishing starts by sanding the drawer to achieve smooth joints over the dovetails. A large amount of time needs to be spent on this step. I begin with a 60 grit to level the surface and then follow up with a 120 grit and then a 200 grit sanding disc on my orbit sander. Between 60 grit and 120 grit is when I use high quality wood filler to fill in the imperfections within the joints.

Step 9:

The finishing method that I personally use is just a water-based satin polyurethane and I apply around 2 or 3 coats finish followed by 220 grit sanding between the coats. This is where the hard work really pays off. The drawer will be strong and it will be quite hard to pull the front off the drawer. I also use a custom branding iron to put my logo on the sides of the drawers.

Step 10:

Installing a good quality under mount or ball bearing slide hardware and drawer fronts where it is needed will be the last step. If everything has been built in a good square, then the process is easy. The 3-inch-tall dovetail drawer will make a great roll-out shelves in kitchen cabinets.

Thank you for reading “Dovetail Drawer Construction Guide” by DC Drawers. Stay tuned for more from the experts at DC Drawers.

Melamine Kitchen Cabinet Pros & Cons

Melamine-Cabinet-Pros-And-Cons

Three things are important when buying cabinets, the style, cost and quality. You can make you choice easier by learning more about melamine kitchen cabinets, including pros and cons.

What’s melamine?

Melamine has a core made from compressed wood particles, which is covered by a paper and resin finish which can be used for manufacturing various colors and styles. It is common for melamine to be used in making cabinets or the bathroom, kitchen or other sections of a home.

Melamine Cabinet Pros:

  1. Pro: Durability

These cabinets are very durable, being resistant to various common problems that occur in the kitchen, from heat, stains and excessive moisture.

The melamine is able to resist external elements due to the tough outer coating, which is also very easy to clean.

  1. Pro: Variety

Being a synthetic material, melamine is able to be produced with a very wide range of finishes. It can come in solid colors, or multiple shades of faux wood grains.

The variety available makes it easy to find the perfect finish for your kitchen.

  1. Pro: Uniformed finish

Melamine can offer consistent finishes, even within the same order because it’s manufactured within a controlled environment. Whereas, solid wood grain can vary in pattern and color, even in the same order.

  1. Pro: Inexpensive

When comparing melamine to solid wood style cabinets, melamine offers a less expensive option. This leads to savings with your renovations or installations, making your budget seem bigger.

Melamine Cabinet Cons?

  1. Con: Weight

While cabinet weight may not be the initial concern, it could require having to upgrade your brackets to a more heavy-duty install. Without having the proper brackets for hanging, cabinets may fall, which could result in more expensive damage.

  1. Con: Melamine chips

While the resin coating on the outside of melamine is durable, it’s still possible to be chipped. In the event chips occur, it exposes the wood particle in the core, which can become rather unattractive. Additionally, if the cabinets chip, refinishing them can become expensive.

  1. Con: More challenging to install

Due to the way melamine is created, these type of cabinets could become harder to install, as it may not work with screws and nails. When improperly used, the screws or nails could cause splintering in the melamine. It is this reason, having a professional installation is recommended with melamine.

  1. Con: It’s susceptible to water damages

In the event water makes its way to the wood particle core and becomes saturated, the overall structural integrity of the cabinet can be compromised. Water absorbs into melamine easier and quicker than with solid wood, so you should keep this in mind if installing next to a sink.

Your decision

If you’re going to the hardwood store, or a furniture store to look for a new set of cabinets, you should take these pros and cons into consideration. Melamine kitchen cabinets, like with various other materials, has good and bad points. However, remember to stay within budget, look for quality and your preferences.

Melamine Veneers vs Wood Veneers on Cabinets

Wood-Melamine-Venners

Veneers

Usually, veneer is a term used to describe a thin layer covering thicker materials. There are many people that think all veneers are wood veneers, but they can also be created using melamine.

Melamine Veneers

Melamine veneer is a thin plastic layer also known as thermofoil. It’s applied using heat onto the plywood or particleboard, as underlying material could vary.

Wood veneers are then wood pieces shaved and added to other pieces of wood, like particleboard or plywood.

Uses for Wood Veneers with Cabinet Interior

Usually, the cabinet interior will have some type of veneer in it, this could be either real wood or melamine veneer.

Uses for Wood Veneers with Cabinet Door

Cabinet doors which uses a hardwood material, such as oak, cherry or maple, the actual wood grain patterns can be seen in the center panel, and usually don’t match up. Advantages of using the wood veneer for the whole center panel is that a consistent grain pattern is provided.

Additionally, wood veneers on a cabinet door could be done over plywood or hardwood, either way the top layer remains wood veneer. Then, paint or stain is added to the wood veneer to match the other part of the cabinet door.

Wood Veneer Grain Patterns

The inconsistent grain patterns that are viewable will depend on the wood veneer and type of wood used by the manufacture. There are certain wood veneers that get manufactured in thin strips, which are six inches wide. In this case, you would see the wood grain strip prior to the next pattern starting. There are certain maple woods that can be produced by manufacturers to have wider veneer sheets, resulting in a more consistent looking grain pattern.

Drawer Connection Inc

Melamine drawer boxes are a solid alternative to traditional dovetailed & plywood drawer boxes. Our melamine drawers are dowel constructed with a particle board core. These melamine drawer boxes allow customization of thickness, material, and your choices of features additions such as accented top edge, notching, box patters, and even more. Stick to your budget and still receive high quality drawer boxes that will last for years. Custom grade for MDF Core melamine’s.

Try our melamine drawer boxes for your next custom bathroom or kitchen project. Give usa call at (877) 917-4887 Melamine Drawer Box colors include almond, black, white, and hard rock maple.

Want to learn more about more about Melamine? Click to read What Are Melamine Cabinets? Shop Cheap Drawer Boxes at DCDrawers.com.

Plywood vs. Melamine Drawer Construction

If you are looking for melamine drawers, plywood drawers, or deciding which type of material to construct your cabinetry from, this post will help.  Kitchen and bathroom drawer construction has multiple materials that can be used to make long lasting, beautiful drawers. Two of the most used drawer construction materials are Melamine and plywood. Both types of material feature products manufactured by compressing wood that forms a solid board. Both Melamine and Plywood have particular advantages that make drawer manufacturers and homeowners choose one or the other. Let’s take a closer look at plywood vs. melamine drawer construction.

Basic Information About Plywood & Melamine Drawer Construction

The follow are things to keep in mind with regards to the strength, weight, cost, density, and environmental impact of both plywood and melamine.

Construction Process Of Materials

Melamine is pressed wood or particleboard that is covered with a plastic coating. Plywood in contrast is solid sheets of wood that have been pressed together with their grains set in opposing directions to increase strength. These materials can break or crack under pressure, but do not split. Either are suitable for drawer construction.

Environmental Safety

Both melamine and plywood contain some small concentration of formaldehyde. Formaldehyde is a naturally occurring chemical which is made up from carbon, oxygen and hydrogen. Both melamine and plywood formaldehyde levels are increased with the application of glue, but can be made with moisture resistant products that make it safe and conform to both European, Japanese, and American standards for safety.

Material Finishes

Melamine is made from the same type of resin that Formica is made from. Melamine being a resin that dries smooth it is perfect for drawer construction because it offers a ready to use surface. It is easy to clean without the need to spend more time with staining or painting the surfaces. Because plywood has more of a natural wood surface it can be prone to defects, knotholes, and rougher surfaces that need to be finished before the drawer can be installed. Because the plywood typically has a visible grain pattern time is also spent trying to make sure that the grain patterns are all going in the same direction.

Production Process

Plywood for drawer construction can be a bit simpler than making them from melamine. It is easier to cut plywood to length because the material is less dense. It is also easier to assemble plywood drawers because the nails and screws go in easier. Plywood drawers are a bit lighter which can be an asset depending on the drawer hardware that will be used. The cutting of melamine is do with CNC routers and is fairly easy. Care must be exercised to not chip the surface of the boards.

Plywood offers a finish and wood grain pattern that many homeowners love. It has the warmth of wood and they love the sight of knots and grain in their cabinet drawers. Other home owners love nothing more than solid colored drawers and complete uniformity. It is really up to the homeowner which style fits their preferences better.

Which Drawer Construction Material Is Best?

When you are deciding between plywood and melamine for a drawer material the choice really is hard. They both have their benefits and it comes down to if you want to be able to see a wood grain in your drawers or if you would prefer a solid color finish that is totally uniform through your kitchen. Melamine is cost effective, easy to clean, and beautiful while plywood has the warmth of wood grain which can make a kitchen feel more custom and one of a kind.


Custom Drawer Construction

Drawer Connection, Inc. has a wide variety of materials, finishes, and hardware to make your kitchen or bathroom drawers exactly how you want them. With options for melamine, plywood, and other composite materials we can fill any order and help finish your project the way you want it done.

 

What Is A Dowel Joint?

 what-is-a-dowel-joint-custom-dowel-joint-drawers

Dowels joints are a way that drawers sections are fastened together. Including dowels in the connecting sections of wood make more accurate, stronger connections that simply using glue alone. Dowel joints are incredibly strong and visually attractive if they are done right. This type of joint is very popular for drawers or other woodworking in which a butt joint is being used. It helps increase the strength and durability of the joint.

What Are Dowel Joints Used For?

Dowel joints are used in a wide variety of woodworking projects. They offer a number of benefits during production and after.

Increased strength – Miter and butt joints are sometimes only glued together. This means that the stresses of whatever use the wood sees will wear on the joint. Humidity can also dry out or cause glue to lose its adhesive properties. Dowels are added to the joints by drilling into each joining piece of wood so the corresponding holes share a dowel.  Having the dowels physically connect the wood dramatically increases strength.

Keeping It Straight – When producing wood products without dowels it can be a challenge to glue and clamp down the pieces without them moving during the drying and setting time. The inclusion of dowels ensures that everything is perfectly lined up and when glued and clamped it is perfectly straight and dries stronger.

Pin Joints – Certain types of joints require the ability to twist. Dowels are generally round in shape, which allows a certain level of twisting. This is easier and more simple than other tail-and-pin joints.

Dowels Work Better Than Biscuits – Biscuit cuts are easier and faster to make but are not as strong or durable. The material is thin and has a possibility to absorb humidity and swell. This can mean a bulge in the joint material and the extra stress can cause it to loosen or fail entirely.

Advantages Of Dowel Joints

No Need For Metal Fasteners – Nails, staples, and screws are fine when found behind sheetrock. For custom drawers or other fine interior cabinetry features they are visually disturbing and upset the grain patterns we all love. Dowels do the job while not being seen.

Increased Durability And Strength – Because the wooden dowel runs inside the connecting wood sections it holds fast and is much stronger. Nails, screws or staples are thinner and many times are not properly installed. They can stretch and splinter the wood making it weaker. This adversely affects the lifespan of whatever wooden structure is being made.

What Are Dowels Made Of?

Dowels can be made from metal, plastic, or more commonly wood. In custom drawer and cabinetry the internal dowel joints are made of wood. For cabinet shelves metal dowels are very common. They are good choices for the moving of shelves. This is good for moving shelves but wooden dowels are used for custom drawer manufacturing as they have increased grain and friction inside the drilled holes and increased durability.


Custom Dowel Joint Drawer Production

Drawer Connection, Inc. has been making customer drawers since 1997 and can produce any drawers you need. Be it dovetail or dowel we can custom make the drawers you want for your kitchen, custom closet organization system, bathroom cabinetry or anywhere else you need to have drawers. Give us a call to get your project started at 1-877-917-4887. Stay tuned for more from the expert drawer box manufacturers at DCDrawers.com

 

Pull Out Drawer Kits

Pull Out Drawer Kits

PULL OUT DRAWER KITS INCREASE STORAGE SPACE

pull-out-drawer-kits

Our new pull out drawer kits are a great way to increase kitchen storage space in less than half an hour. The pull out drawers include 2 dovetail drawers, full extension slides, ball bearing glides, and all the hardware and electrical materials you need to install pull out drawers yourself (DIY).

It’s as easy as attaching the mounting brackets to the drawers and securing the kit to the cabinet bottom.

Affordable Pull Out Drawer Kits For Sale

PULL OUT DRAWER KITS WITH POWER OUTLETS

pull-out-drawer-kits

Pull Out Drawer Applications

New! All power outlets come with adjustable read bracket mounts for easy installation!

Upgrade your kitchen drawers with pull out drawer kits with power outlets and be able to charge all of your devices inside your kitchen drawers. These pull out drawers with power outlets work great for home, office, closet, locker rooms and more. The purpose of these drawer boxes with power outlets is to get all of those chords and chargers out of the way. Order your pull out drawer kit with power outlets online by clicking the order now button below.

Features Of Power Outlets

  • First power outlet used in drawer boxes
  • Safety features that interlock and cut power
  • Adjustable rear bracket gives room for fine tuning
  • Simple to install and easy to specify

Buy Pull Out Drawer Kits For Sale

PULL OUT DRAWER KIT SPECIFICATIONS

pull-out-drawer-kits

pull-out-drawer-kit-specifications

kitchen-cabinet-specifications  receptacle-specifications-for-pull-out-drawers

applications-for-pull-out-drawers

All of our pull out drawers measure 2″ tall and 22″ deep to increase storage space and improve access to your cabinets.

We include a 1 year warranty on all pull out drawer parts and hardware.

Drawer glides can hold up to 100lbs (drawer weight included).

BENEFITS OF DRAWERS WITH POWER OUTLETS

pull-out-drawer-kits

Maximize Space. Clear the clutter off of your countertops. These pull out drawers with electrical outlets are great for bathrooms, bars, bathrooms, offices and more.

Safety In Mind. These power outlet equipped drawers have circuit breaker safety features built-in that prevent high power devices form being used for safer operation.

Reliability. These drawer boxes with power outlets are made with high quality wood and electrical materials. These drawer slides are tested over half a million times for a lifetime of operation.

PULL OUT DOVETAIL DRAWER WOOD OPTIONS

pull-out-drawer-kits

Our pull out dovetail drawers can be prefinished in a variety of hard wood types including; maple wood, white, black, hard rock or almond melamine wood or Baltic birch wood. View all drawer styles and colors in our drawer gallery.

Maple Pull Out Drawers For Sale
Maple Wood
Birch Wood Pull Out Drawers
Birch Wood
Buy Hard Rock Melamine Pull Out Drawers For Sale
Hard Melamine Wood
White Melamine Pull Out Drawers
White Melamine Wood
Black Melamine Pull Out Drawers
Black Melamine Wood
Almond Melamine Pull Out Drawers
Almond Melamine Wood

DRAWER KIT INSTALL INSTRUCTIONS 

pull-out-drawer-kits

Confirm Drawer Specifications For Power Outlet Installation

Pull Out Drawer Kit With Power Outlets

  1. Review the depth of the cabinet to make sure you have the right size extension for the drawer to open completely.
  2. Review the width you have available behind your drawer box to make sure the power outlet will fit.
  3. Review the space behind your drawer box.
  4. Review the height of the interior part of the drawer box to have enough space for the receptacle box.

Custom pull out drawer kits can be shipped in about 5 business days. 2 drawer pull out kits can accommodate bigger or taller items.

ORDER PULL OUT DRAWER KITS ONLINE

pull-out-drawer-kits

DRAWER CONNECTION INC - NATIONWIDE PULL OUT DRAWER MANUFACTURER
NATIONWIDE SHIPPING

To order your pull out drawer kits online, visit our online store or give us a call at 1 (877) 917-4887 for more information. Also, view the Pull Out Drawer Kit Brochure for more information about drawers with power outlets. Stay tuned for more from the expert drawer box manufacturers at DCDrawers.com

Welcome To DC Drawers Blog

Custom Dovetailed Drawers

At Drawer Connection (DC Drawers), our philosophy is to “give customers the drawer quality they deserve at a price they can afford.” And we have been doing just that since 1997. We provide our customers with the highest quality materials, craftsmanship and customer service. Our dedication to exceeding your expectations ensures that you will receive a high-quality product, complete to your specifications, and on time.

We take pride in providing the best service – no matter how large or small your custom drawer order. Our team works hard to assist your business by cutting production time, increasing profits and delivering absolute customer satisfaction.

We have enjoyed phenomenal growth in our customer base since our inception, due in large part to the loyalty of our valued customers. I want to personally thank you for your trust and confidence in choosing Drawer Connection, Inc. for your custom drawer manufacturing needs. By using our online ordering system, it ensures accuracy and saves valuable time in placing orders.

Let us show you how we can help save you time and money. If you have any questions, please do not hesitate to contact me directly at (877) 917-4887. About Drawer Connection, Inc. Mesa AZ | DC Drawers

Thank you,

Steve Harmon
President/CEO